WORLD GT Rubber Tire (WGT-R) 17.5 motor using ROAR approved 1s "Blinky" ESC or 2s with booster-- NO RECEIVER PACKS. Spec Tires, rubber only. Battery: 1s ROAR approved 3.7v l lipo battery. Single speed only. Single, one-piece drive axle only. No independent suspension allowed. World GT-R approved body. Wing must be fastened to the rear deck of body. Rear Wing may not be higher than roof height. Minimum 5mm ride height under all parts of the vehicle excluding the spur gear. Roll Over antennas are not allowed. Read Bodies and Complete Rules Set
Mini Z Pure Stock
Min. Weight: (With batteries) 170g
Wheel Base: 98mm - 102mm
Max Car Length: 178mm
Max Car Width: 80mm
Max Car Height: 45mm
PCB/ELECTRONICS Requirement:
Kyosho 27Mhz / 2.4Ghz ASF/ FHS/FHSS AM band Mini-Z circuit board only.
*** (No EV or aftermarket electronic or ESC such as NOVAK or TEKIN. )
Motor: OEM
Car Body: Kyosho Mini-Z and Kyosho Autoscale Bodies.
Chassis: Kyosho MR-02 and MR-03 chassis allowed
Option Parts: Items included in Kyosho Circuit Pack MZW2019C
Rims: Rims must fit within the width of the car body
Tires: MR03 OEM or Kyosho MZW-37-20, MZW38-30, MZW39-30. Foam tire and traction compound is not allowed.
Batteries: AAA size batteries 4 cell, alkaline, NiMH or NiCd only. Lithium, LIoN or Lipo battery not allowed.
Frequency: 2.4G ASF, FHS, FHSS
Transmitter: OEM 27 MghZ and 2.4ghz: Perfix KT-18, Synchro KY-531P, Perfix KT-19
Gyro: Not Allowed
5/2020
Euro Semi-Truck This is a pure box stock class open to any skill level hobbyist. 1. Legal kits: Item 58632 RC Team Hahn Racing MAN TGS (TT-01 type E chassis) & Item 58642 RC Team Reinert Racing MAN TGS (TT-01 type E chassis) 2. The kit must be built exactly per the instruction manual. 3. The ONLY Hop-Op Option permitted is Ball Bearings. 4. Must use stock pinion and spur gear. 5. The kit Tamiya TBLE-02S ESC and kit supplied motor must be used. Battery connector may be changed to DEANS. Motor Bullet connectors may not be removed. 6. All body parts must be used. 7. Body may be painted in any scheme. 8. Must use kit tires and wheels. Kit tires may be glued onto wheel. 9. Any grease or lube may be used to lubricate gears or moving parts. 10. Batteries: Any Reedy Wolf-Pack or Peak Racing Powermax round-case LiPo battery may be used for this class.
Plastic Tub Chassis Class -- This class is a blend of the Tamiya TT and Vaterra Classes that allows several shaft drive entry level platforms.
Legal chassis platforms: Any Tamiya TT-01 or TT-02 on-road chassis, Vaterra V100, HPI Sport 3, Carisma M40S or Traxxas 4-Tec 2.0 Compete Rule-set Here
1/12th SCALE STOCK ROAR 17.5 spec motor using approved Spec ESC. This is often referred to as Blinky mode for the ESC signified by a blinking led on the esc when car is in neutral. Foam tires, GTP, Can-Am or WSC body. Powered by a 1S 3.7V cell. Single speed only. Single, one-piece drive axle only. No independent suspension allowed. Wheel arch cut-outs: Maximum 10 mm over tire diameter. Ground clearance: Minimum 3mm under all parts of the vehicle excluding the spur gear. The use of a rollover antenna is permitted.
1/12th GT Commercially available Pan Car Chassis. Reedy 21.5 Fixed Timing Motor (ASC297) with 295 rotor using ROAR approved 0 degree timing “blinky” Spec ESC.
BSR or CRC Spec purple stripe foam tires. Rear tires should NOT be trued.
Powered by a 1S 3.7V single cell, ROAR approved hard case battery. Ground clearance: The use of a rollover antenna is permitted.
Minimum Weight - 730 grams
Maximum Width - 172 mm
Minimum 3mm under all parts of the vehicle
Spec/Fixed Gear 78T Spur & 45T Pinion
Bodiy Shells Permitted
Budies are to be cut to trim lines (NO SLAMMING) Wing required and must be cut to full width of the body. Wing can be trimmed to any height. Wheel arch cut-outs: Maximum 5 mm over tire diameter.
Bitty Design Agata (BDYGT12-AGT)
Bitty Design LS 3 (BDYGT12-LS3)
Bolink Kremer Porsche 935
Bolink Porsche 935
Bolink 280Z IMSA GTU
Bolink Greenwood Corvette
Bolink 930 Lemans Porsche
Bolink Dekon Monza
Bolink RX7 IMSA GTU
Kamtec Lotus GT1 (Kamtec part no. GT01)
Kamtec Ascari GT3 (Kamtec part no. GT02)
Kamtec Aston Martin (Kamtec part no. GT03)
Kamtec Type F (Kamtec part no. GT04)
Kamtec Porsche GT3 (Kamtec part no. GT05)
Mardave Mardave Lotus GT1 (Mardave part no. V140)
Mardave Ascari GT3 (Mardave part no. V151)
Mardave Aston Martin (Mardave part no. V160)
Mardave GT2 (Mardave part no. V131)
Mardave Porsche (Mardave part no. V113)
Mardave Ginetta (Mardave part no. V161)
Montech (MTB-018-012) (MTB-018-012L)
Penguin Custom Bodyshells
Lambo GT12 (part number PEN01)
Protoform
Protoform PF-M12 (Protoform part no. #1613-30)
Protoform C8 Corvette ( part no.PRM1575-20)
Schumacher/Screwz4RC
Supastox GT12 Type A, (part number G888) (SCHG904)
Supastox Gt12 Body Type AM, (part number G898)
Supastox GT12 Type AU, Audi R8, (part number G903)
Supastox GT12 Type F, (part number G905) (SCHG905)
Supastox GT12 PGT3R (SCHG908)
Zen-Racing
Zen-Racing GTM (part number PBGT02)
Zen-Racing GTF (part number PBGT03)
US VINTAGE TRANS-AM (VTA) Rules Heat and Mains are 6 minutes. Our track deviates from those rules in the respect of race times heats and mains are 6 minutes, no driver figure required and any ROAR stock spec (Blinky) ESC can be used.
USGT – Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension.
4wd 1380g weight Fwd NO weight limit
Any 190mm or 200mm body….body can be any body that’s not on the ROAR T2 body list.
Any molded wings can be used. Lexan wings 10mm maximum height / side dam height
Tires-Any treaded (non–slick) rubber tire available 24 or 26mm, Must use a non-molded (ex. open cell foam) insert. Wheels- Any 24 or 26mm spoke (non-dish) type wheel. Motors- 21.5 with Blinky Speed Control. 6 minute qualifiers - 6 minute mains. ROAR approved hard case batteries
USGT Spec 21.5 Motor
Driver figures NOT required
TOURING CAR STOCK (TC Stock Blinky): ROAR Spec 17.5 motor using approved Spec ESC. Rubber tires, 2s, 7.4v nominal lipo battery, single speed only, idependent suspension front and rear. Only 4WD cars allowed. Body must resemble 2 or 4 door cars that have raced in a Touring Car Series. Only one wing is allowed, fixed to the same place as the wing on the full-size vehicle. The wing must be fastened to the rear deck of the body, not directly to any part of the chassis of the vehicle. No part of the wing may extend above the roofline of the body. 5mm ground clearance under all parts of the vehicle excluding the spur gear.
Formula 1
Motor: ROAR 25.5
ESC: ROAR-Legal ESC set on non-boost.
Tires: Rubber only, F1 scale. Must be available to the general public (FN2).
Body: F1 scale, molded front/rear wing (FN3).
Drive: 2-wheel rear drive cars only
Width: 190mm max
Wheelbase: 270mm max
Battery: 2S LiPo or 6-Cell NiMh, long or short packs
Battery Max Voltage: 8.44v (FN4)
Minimum Weight: 1050g
Minimum Ride Height: 3mm
Suspension: All suspensions allowed, including IFS suspensions
Driving Aids: None allowed
Additional F1 Rules: http://uf1rc.com/rules-and-regulations/
2WD Short Course Truck – Any 1/10 2wd trick with 4 wheel independent suspension.
Tires: Slcks Only (absulutely no tread, pins or paddles) Only tires commercially available.
Wheels: Only 2.8" wheels specifically produced for 1/10 SCT
Body: Any body designed for SCT that fully extends beyond the tires on all four corners of the vehicle
Wings: No wings or spoilers permitted
Batteries: 7.2vl lipo max. or 8.4v NiMH max. Lipos must be ROAR approved hard case batteries.
Motor: Unrestricted
ESC: Unrestricted